Permanent Magnet Motor High Twist Motors CW CCW For DIY Feature:1. The DC motor adopts accuracy treatment, magnetic material processing and insulation treatment, and its function is stable and reliable.2. The DC motor has a large turn, not only has low noise, but also has stable operation.3. The motor adopts wear-resistant metal gears, which can prevent teeth from cracking and prolong the service life of the motor.4. The motor adopts pure copper wire, which has the characteristics of low temperature and low loss.5. The DC motor can work with a regulator to control the speed, and it can be CW and CCW. Specification:Item Type: DC Permanent Magnet MotorItem Type: DC Permanent Magnet MotorModel: 31ZYType: DC Permanent Magnet MotorRated Voltage: 6-24(V)Parameters: (corresponding to the following table according to the title speed) using voltage Vnect voltage(V)6V12V12V24V24V24VBaload current(mA)le; 180le; 110le; 350le; 40le; 100le; 200No charging speed (rpm)400040008000350050008000Znamionowy steering (g.cm)100100200120200200Prędkość rated (rpm)320032006500290840006600Prąd rated (A)le; 0.8le; 0.5le; 1.6le; 2.3le; 0.6LE; 1.0Locked rotor twist (g.cm)ge; 500ge; 600ge; 1000ge; 669ge; 850ge; 1200Blocked rotor current (A)le; 3.3le; 2.3le; 6.5le; 1.06le; 2.0le; 4.4CCM2 DC Motor Speed Controller Product OutputDC Drive Controller CW Control CCWThis governor adopts PWM speed control technology, which has the characteristics of high conversion efficiency, wide speed range and stable operation. All of them use imported original STMicroelectronics chips, which have been tested for voltage, current, function, etc. before leaving the factory, and the circuit is stable and reliable. Technical Parameter:Model: CCM2Working Voltage: DC10V-30V Power Control: 12V x 3a = 36W, 24V x 3a = 72W Greater than 24V, Maximum 120W Rated Current: 3A Maximum Current : 5A PWM Pulse Width Adjustment Range: 5%-95% Potentiometer: B10K Resistance Value, Wire Length 20CM, Hole 8mm, Output Voltage: About 0- Input Voltage Speed Controller Size: Approx. 74x47x28mm / 3x2 x 1.1in Potentiometer is used to adjust the speed CW CCW switches are used to control the CW, CCW and stopAttention:Motor1. There should be no binding objects when using the motor. For example, the adhesive should not flow to the bearing through the rotating shaft, which would hinder the operation of the motor.2. Shaft rotation can have the opposite effect on the life of the motor. To extend the service life, check that your load complies with the regulations. Do not overload or have objects that impede rotation at the end of the shaft.3. Produced in eccentric high radiation load, which is harmful to the life of the engine.4. Do not store in ambient high temperature or extreme humidity, and do not put in corrosive gas, which will reduce the effect of the engine.5. Do not start the engine in the surrounding high temperature and humidity.6. When soldering is needed at the positive and negative terminals of the power supply motor, the temperature of the soldering iron is 340°C ± 40°C, and the heating time is 3 seconds. Do not deform the plastic. Allow the solder point to flow into the motor or break the end of the wire during operation. The function of the engine decreases.7. Do not let the motor shaft get stuck. After the power is supplied, the motor will overheat in a short time and its accessories will be burned.8. Due to the lack of skills of the staff, the quality of the engine cannot be guaranteed when it encounters the things mentioned in the manual, or superficial judgment is obviously a mistake.9. Specify the specific power and make sure it is within the range of measurable requirements.10. The installation of pulleys or gears should not be abnormally deteriorated when pressed.11. When installing the motor, if the screw is too long, it will cause between the motor itself and the rotor, which will affect the characteristics. Governor1. The input of the DC motor speed controller is DC, and it cannot be directly connected to AC (such as household 220V AC motors), otherwise it will burn out.2. The positive and negative poles of the DC power supply cannot be reversed, otherwise the regulator will be damaged.3. The motor can be positive or negative. When the direction of travel is not as expected, the direction can be changed by adjusting the wire sequence.4. The potentiometer knob can change the duty cycle of the regulator output, thus changing the speed of the motorPackage List:1 x Motor1 x Governor1 x CW CCW Switch1 x Knob1 x WasherNote: 1) We accept Alipay, West Union, TT. All major credit cards are accepted through the payment processor's secure escrow. 2) Payment must be made within 3 days of placing the order. 3) If you can't check out immediately after the auction ends, please wait a few minutes and try again, payments should be completed within 3 days. About Shipping 1.